Toyota Yaris Vitz Belta 2G fuse and relay

Toyota Yaris 2nd generation was produced in 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 and was designated as P90. During this time, the model has been restyled. This vehicle has been delivered all over the world. Also known as Toyota Vitz / Toyota Belta in some countries. A distinctive feature of the models is the steering position side. In this publication you can find a description of the locations of electronic control units, the purpose of fuses and relays Toyota Yaris / Vitz / Belta 2 with box diagrams and photo examples of their execution. Note the cigarette lighter fuse.

The arrangement of the boxes and the purpose of the elements in them may differ from the one presented. Check the designation of the elements with your diagrams on the box cover.

Passenger compartment

Location

General layout of control units in the passenger compartment

LHD

RHD

Assignment

1. Rear Fog Light Relay
2. Fuse Box
3. Front Fog Light Relay
4. Main Body ECU
5. with Entry & Start System: Accessory Relay (ACC)
   without Entry & Start System: Accessory Relay (ACC Cut)
6. Additional Fuse Box
7. Steering Lock ECU
8. Power Steering ECU
9. Multi-mode Manual Transmission ECU
10. Starter Relay (ST CUT)
11. LHD: Running Light Relay
12. Power Management Control ECU
13. Engine Stop and Start ECU
14. Junction Block
15. Transponder Key Amplifier
16. Airbag Sensor Assembly Center
17. Shift Lock Control ECU
18. A/C Amplifier
19. Junction Block
20. RHD: Theft Warning ECU
21. RHD: Turn Signal Flasher
22. RHD: Theft Warning ECU (TMC Made From Aug. 2008)
23. RHD: Double Door Lock ECU

Fuse box

It is located under the dashboard, for access you need to remove the protective cover.

LHD

RHD

Diagram from the box cover

Photo example of execution

Diagram

Designation

For the cigarette lighter, there is a fuse number 8, 15A, marked on the lid as CIG.

The individual elements are attached to the top of the unit.

Diagram

Appointment

Diagram

Assignment

1. ACC relay
2. Ignition system relay
3. Heater relay
4. Rear fog lamp relay
5. Front fog lamp relay
6. 1) 30A Bodywork ECU / Window Electrician (POW) 2) 30 / 40A Heated rear window DEF, fuse: “MIR HTR”

Additional fuse box

Diagram

Protected components

Additional elements

Diagram

1. Door Control Receiver
2. Stop Lamp Relay

Engine compartment

Location

General layout of electrical control units under the hood

LHD

RHD

Assignment

1. Fuse Box
2. without Daytime Running Light: Relay Box
3. with Daytime Running Light: Relay Box No.2
4. Engine ECU
5. Fusible Link Block
6. Glow Plug Relay
7. Skid Control ECU with Actuator

Fuse and relay box

Located on the left side of the engine compartment.

Photo – example

Example of a diagram from the box cover

Diagram

Designation

Relay box

Diagram

Circuits protected

Additional relay box

Type A

• R1 Vehicle Stability Control (VSC1)
• R2 Vehicle stabilization system (FR DEF / VSC2)

Type B

• R1 PTC heater (HTR SUB3)
• R2 PTC heater (HTR SUB2)
• R3 Headlight / Multi-mode manual transmission / PTC heater (H-LP / AMT / HTR SUB1)

Power fuse box

It is located on the positive terminal of the battery.

Diagram

Appointment

1. 80A GLOW DC / DC – Diesel: Multiport fuel injection system / sequential multiport fuel injection system
2. 60 / 80А MAIN – Fuses “EFI”, “HORN”, “AM2”, “ALT-S”, “DOME”, “ST”, “ECU-B”, “ETCS”, “HAZ”, “H-LP” LH / H-LP LO LH “,” H-LP RH / H-LP LO RH “,” AMT “
3. 120A ALT – Charging system, fuses HTR SUB2 “,” EPS “,” ABS1 / VSC1 “,” HTR “,” ABS2 / VSC2 “,” HTR SUB1 “,” RDI “,” DEF “,” FR FOG “,” OBD2 “,” D / L “,” POWER “,” RR DOOR “,” RL DOOR “,” STOP “and” AM1 “fuses

That’s all. If you know how to make the material better, write in a comment.