Mercedes-Benz Actros MP4 provides the 4th generation of the Actros range, which was produced in 2013, 2014, 2015, 2016, 2017, 2018. In this post, we will show a description of the fuses and relays Mercedes Actros mp4 with a box diagram and its location. Note the cigarette lighter fuse.
The diagram do not fit or the wrong generation?
[Description of Mercedes Actros mp1]
[Description of Mercedes Actros mp3 and mp2]
Contents
Fuse and relay box
The main fuse and relay box is located in the passenger compartment, at the bottom of the instrument panel on the passenger side.
To gain access, open the locks (2) and remove the cover (1).
The execution of the box and the purpose of the elements in them may differ from those presented and depend on the year of manufacture and the level of electrical equipment. Check the designation with your diagrams on the back of the protective cover.
Type 1
Type 2
Layout
Assignment
- Relay module A32
- Fuses, relays and diodes in the main module (GM)
- Relay module A31.
- Fuses for modules A1 and A2.
Relay module A32
- K1 – Heated windscreen
- K2 – Heated windscreen
- K3 – Additional headlight – clamp 56a
- K4 – Reserved
- K5 – Reserved
- K6 – Reserved
Master Module (GM)
SCA
Circuit breakers
F2 | 20A Driver’s door control unit |
F3 | 20A Front passenger door control unit |
F4 | 20A Drive control system |
– | 20A Tachograph – clamp 30 |
F5 | 15A Programmable special module |
– | 15A Distributor – clamp 30 |
F6 | 25A Fan |
– | 25A Independent electric air conditioning |
F7 | 25A Radio/navigation system |
– | 25A 12V voltage transformer |
– | 25A Distributor – clamp 30 |
F8 | 20A Cool box |
– | 20A Additional heating system |
– | 20A 12V voltage transformer |
– | 20A Adaptive Drive Prediction Control Unit – Clamp 30 |
– | 20A LSVA (heavy duty charges based on vehicle capacity) |
F9 | 10A Diagnostic connector |
F10 | 10A Heating system |
– | 10A Distance sensor |
– | 10A Driver assist system – terminal30 |
F11 | 10A Toll Collect System |
– | 10A Lampshades for lighting the additional compartment in the rear wall |
– | 10A Reading lamp |
– | 10A Telephone |
– | 10A Tire pressure monitoring system |
– | 10A Fleet management system – clip30 |
– | 10A ERA‒GLONASS |
F12 | 15A Sliding sunroof |
– | 15A EDW system (anti-theft alarm system) |
– | 15A LSVA (heavy duty charges based on vehicle capacity) |
– | 15A Steering angle sensor |
F13 | 25A Ride Height Control System |
– | 25A Hydraulic clutch (retarder turbo clutch) |
– | 25A Retarder |
F14 | 10A Body builder – clamp30 |
F15 | 20A Trailer |
– | 20A Trailer voltage transformer – terminal 30 |
F16 | 20A Trailer ABS – clamp 30 |
F17 | 5A Ignition switch |
– | 5A Central Gateway |
F18 | 5A Modular Switch Panel |
– | 5A Voltage transformer with remote output |
– | 5A Instrument cluster – terminal 30 |
F19 | 6A Cigarette lighter |
– | 15A Power socket – terminal 15 |
F20 | 20A Seat heating system |
– | 20A Distributor – terminal 15 |
F21 | 15A Fuel pre-filter heating system with water separator |
– | 15A Distributor – clamp D+ |
F22 | 10A Body builder – terminal D+ |
– | 10A Fuel pre-filter heating system with water separator |
F23 | 5A BlueTec® exhaust gas aftertreatment |
– | 5A Sunblind |
– | 5A Drawbar (lower drawbar mounting system) |
– | 5A Toll Collect System |
– | 5A MEILLER retrofit mounting socket |
– | 5A Auxiliary Hydraulic Actuator (HAD) – Clamp 15 |
– | 5A ERA‒GLONASS |
F24 | 5A Instrument cluster |
– | 5A Battery disconnector |
– | 5A Tachograph |
– | 5A Brake system |
– | 5A Airbag |
– | 5A Telephone |
– | 5A Transmission control system |
– | 5A Fleet management system |
– | 5A Additional headlight |
F25 | 10A Trailer ABS |
F26 | 10A Drive control system |
– | 10A Parameterizable special module – terminal 15 |
F27 | 10A Engine control – terminal 15 |
– | 10A Reversing camera |
– | 10A Driver assistance system |
– | 10A Adaptive Drive Prediction Control Unit – Terminal 15 |
F28 | 10A Retarder |
– | 10A Hydraulic clutch (retarder turbo clutch) |
– | 10A Electronic air preparation unit – terminal 15 |
F29 | 15A Transmission control system – terminal 30.1 |
– | 15A CB service radio |
F30 | 20A Brake system – clamp 30.2 |
F31 | 15A Trailer brake light |
F32 | 25A 24V sockets |
– | 25A Additional 24V socket |
F33 | 10A Lights for additional roof compartment |
– | 10A Voltage transformer with remote output |
F34 | 25A 24V high power socket |
– | 25A 12V voltage transformer |
– | 15A Other body electrical equipment |
F35 | Spare |
F36 | 20A Electronic air preparation unit – terminal 30 |
F37 | 15A Transmission control system – terminal 30.2 |
Relay
- K1 – Reinforcement – clamp 15
- K2 – Reinforcement – clamp D+
- K3 – Reinforcement – clamp 15
- K4 – Oil cooled gearbox
- K5 – Reinforcement – clamp 15
- K6 – Trailer brake light
- K7 – Bistable relay
- K8 – Bistable relay
- K9 – Reserved
SSAM
Circuit breakers
F1 | 20A Brake system – terminal 30.1 |
F2 | 10A Diagnostic connector |
F3 | 15A Additional heating system |
– | 15A Control unit for the system of adaptive prediction of running parameters |
– | 15A 12V voltage transformer |
F4 | 10A Toll Collect System |
– | 10A Steering angle sensor |
– | 10A Telephone |
– | 10A Fleet management system |
– | 10A Tire pressure monitoring system |
– | 10A Lights for additional compartment in the rear of the vehicle – clamp 30 |
– | 10A ERA‒GLONASS |
F5 | 15A LSVA (heavy duty charges based on vehicle capacity) |
– | 15A Sliding sunroof |
– | 15A EDW system (anti-theft alarm system) |
– | 15A CB service radio |
F6 | 10A Heating system |
– | 10A Driver assistance system |
– | 10A Reading lamp – clamp30 |
– | 10A Distance sensor |
F7 | 20A Electronic air preparation unit – terminal 30 |
F8 | 25A Ride Height Control System |
– | 25A Retarder |
F9 | 10A Body builder – clamp15 |
– | 10A Toll Collect System |
– | 10A BlueTec® exhaust aftertreatment system |
– | 10A ERA‒GLONASS |
F10 | 20A Trailer brake light |
– | 20A Bodybuilder installed brake light |
F11 | 20A Programmable special module |
– | 20A Cold box clamp 30 |
F12 | 20A Drive control system |
– | 20A Tachograph – clamp 30 |
F13 | 25A 12V voltage transformer |
– | 25A Radio/navigation system – clip30 |
– | 25A Hydraulic clutch (retarder turbo clutch) |
F14 | 10A Body builder – clamp30 |
F15 | 15A Transmission control system – terminal 30.1 |
F16 | 10A Trailer ABS |
F17 | Spare |
F18 | 15A Seat heating system |
F19 | Spare |
F20 | 25A 24V high power socket |
– | 15A Other body electrical equipment |
– | 15A CB service radio |
F21 | 15A Fuel pre-filter heating system with water separator |
– | 15A Distributor – clamp D+ |
F22 | 10A Body builder – terminal D+ |
10A Fuel pre-filter heating system with water separator | |
F23 | Spare |
F24 | Spare |
F25 | 20A Trailer ABS |
F26 | 20A Trailer |
20A Trailer voltage transformer – terminal 30 | |
F27 | 20A Driver’s door control unit |
F28 | Spare |
F29 | 20A Front passenger door control unit |
F30 | Spare |
F31 | Spare |
F32 | 10A Lights for additional roof compartment |
– | Voltage transformer with remote output |
F33 | 25A 24V sockets |
– | 25A Additional 24V socket |
F34 | Spare |
F35 | 25A Fan |
F36 | 5A Auxiliary hydraulic drive (HAD) |
– | 5A MEILLER retrofit mounting socket |
– | 5A Tachograph |
– | 5A Instrument cluster |
– | 5A Brake system |
– | 5A Additional headlight |
– | 5A Airbag |
– | 5A LSVA (heavy duty charges based on vehicle capacity) |
– | 5A Control unit for the system of adaptive prediction of running parameters |
– | 5A Telephone |
– | 5A Fleet management system |
– | 5A Transmission control system |
– | 5A Battery Disconnect – Terminal 15 |
F37 | 20A Brake system – clamp 30.2 |
F38 | 10A Driver assistance system |
– | 10A Reversing camera |
– | 10A Engine control – terminal 15 |
– | 10A Swap body – clip 15 |
F39 | 15A Transmission control system – terminal 30.2 |
F40 | 10A Drive control system |
– | 10A Parameterizable special module – terminal 15 |
F41 | 10A Retarder |
– | 10A Electronic air preparation unit – terminal 15 |
F42 | 5A Cigarette lighter |
– | 15A Power socket |
Relay
- K1 – Reserved
- K2 – Reinforcement – clamp D+
- K3 – Oil cooled gearbox
- K4 – Reinforcement – clamp 15
- K5 – Reinforcement – clamp 15
- K6 – Trailer brake light
- K7 – Reinforcement – clamp 15
- K8 – Bistable relay
- K9 – Bistable relay
Relay module A31
Diagram
Appointment
K1 | Working headlight |
– | Swap body |
K2 | Oil cooled transfer case |
K3 | Fuel pre-filter heating system with water separator |
K4 | Tail lift |
– | Disable Auxiliary Hydraulic Drive (HAD) |
K5 | Tail lift |
– | Disable Auxiliary Hydraulic Drive (HAD) |
K6 | 12V radio – terminal 58 |
K7 | 12V radio – clamp 15R |
– | Subwoofer |
K8 | Additional headlight – clamp 58 |
K9 | Low roof interior lighting |
K10 | Low roof interior lighting |
Modules A1 and A2
Diagram
Decoding
A1 | |
F1 | 5A Cab tilt pump |
F2 | 10A Tail lift |
F3 | 10A Flashing beacon |
F4 | 10A Work lamp |
– | 10A Swap body |
F5 | 10A Illuminated three-pointed Mercedes-Benz star |
– | 10A Hand lamp socket |
F6 | 15A Other body electrical equipment |
F7 | 25A Heated windscreen |
F8 | 25A Heated windscreen |
F9 | 10A Oil cooled transfer case |
– | 10A Auxiliary hydraulic drive (HAD) |
F10 | 15A Fuel pre-filter heating system with water separator |
F11 | 20A Independent electric air conditioning |
F12 | 15A Auxiliary hydraulic drive (HAD) |
F13 | Spare |
F14 | Spare |
A2 | |
F1 | 10A MEILLER retrofit mounting socket |
F2 | 20A Other body electrical equipment 2 and 3 |
– | 20A Body aux axle switch |
F3 | 10A Steering tag axle |
F4 | 15A Additional headlight |
F5 | 10A Air control system |
F6 | 10A Subwoofer |
F7 | 5A Equipment in accordance with the regulations for the transport of dangerous goods by road, for England |
F8 | 5A Low roof interior lighting |
F9 | 5A CB service radio |
F10 | 15A Radio/navigation system |
F11 | 5A Electric independent air conditioning system |
– | 5A Antenna amplifier |
– | 5A Cornering assistant |
F12 | 10A 12V radio receiver |
F13 | Spare |
F14 | Spare |
Additional Information
Some fuses don’t have the usual look you’re used to seeing in cars, but their functionality is the same. Conventionally, all of them can be divided into fusible and automatic.
Checking the fuse
- Remove the fuse from the module using pliers and visually inspect it.
- If the fuse wire is blown, replace the defective fuse with a backup fuse.
- Turn on the consumers of electricity and check their performance. If the fuse blows repeatedly, have the electrical equipment checked by a qualified specialist workshop.
Checking the automatic fuse
When the automatic fuse is activated, the pin (4) moves to the off position (2).
- Remove the automatic fuse from the module.
- Press the pin (4) to the on position (1).
- Click on the release (3).
– If the pin (4) moves to the off position (2), the circuit breaker is OK.
– If the pin (4) does not move to the off position (2), the automatic fuse needs to be replaced. - Press the pin (4) to the on position (1) and reinsert the automatic fuse.
- Turn on the consumers of electricity and check their performance. If the automatic fuse blows again, have the electrical equipment checked by a qualified specialist workshop.
That’s all. There is something to add – write in the comments.
Hello, my truck air conditioning fan system is not working, can any help me? Actros is mp5.
Hello,is there a fuse or relay that can stop the engine for actross when you remove it
HELLO,IS THERE A FUSE REALY THAT CAN STOP THE ENGINE FOR ACTROS WHEN REMOVED?
Can l have brake circuit diagram for actross 2015